Research peptides held in Australian stock, every lot tested by HPLC and mass spectrometry. For laboratory research use only.
Cart 0

PT-141 Dosage Calculator: Vial Reconstitution and Units

PT-141 Reconstitution Calculator

Concentration
Amount in 0.1 mL
Volume containing the target amount

Same volume on a U-100 syringe scale

Mixing a 10mg PT-141 Vial

This PT-141 dosage calculator turns a vial size and a water volume into a concentration and a syringe reading. Add 2 mL of bacteriostatic water to a PT-141 10mg vial and the stock comes out at 5 mg per mL. At that strength, a single graduation on a U-100 syringe carries 50 mcg.

Melanotan II also ships as a 10mg vial, so the maths is identical, and it sits in the preset list beside PT-141.

Reconstitution table for PT-141

Each row pairs the vial with a water volume and shows the resulting strength. Remember that 100 units on a U-100 insulin syringe equals 1 mL, and 10 units equals 0.1 mL.

Vial sizeBac water volumeResulting strengthIn 10 units (0.1 mL)In 1 unit
10 mg1 mL10 mg/mL1 mg (1000 mcg)100 mcg
10 mg2 mL5 mg/mL0.5 mg (500 mcg)50 mcg
10 mg3 mL3.333 mg/mL0.333 mg (333.333 mcg)33.333 mcg

Two equations behind the PT-141 dosage calculator

Strength in mg/mL equals the milligrams of PT-141 in the vial ÷ the millilitres of water you added

Syringe units (U-100) equal the target in mg ÷ the strength in mg/mL, then × 100

Convert any microgram figure to milligrams by dividing by 1,000 before you start. This tool is pure arithmetic. It never suggests an amount, and every AminoLab PT-141 vial is sold for laboratory research use only to adults 18 and over.

Buy PT-141 Online in Australia, Vial or Spray

Shop the 10mg PT-141 vial, the size every example above is built around. A ready-to-use nasal spray format is listed on that same product page for projects that call for it. Add bacteriostatic water to the cart, or look over Melanotan II as a comparison compound. Instead of hunting for PT-141 near me, read the lot certificate online first, then order straight from stock held here in Australia.

PT-141 Calculator Explained

How Each of the Four Outputs Is Worked Out

First, the tool takes the 10mg of PT-141 (bremelanotide) and divides it by the diluent you entered, which gives mg/mL. Next it multiplies that figure by 100 to report the micrograms held in 0.1 mL, which is the first ten marks on a U-100 syringe. Your microgram target is then divided by the concentration to produce a volume in millilitres, and that volume times 100 becomes the unit reading.

Worked Example, 500 mcg From a 10mg Vial

  • With 1 mL of bacteriostatic water the stock is 10 mg/mL, meaning 0.1 mL carries 1,000 mcg and the 500 mcg target needs 0.05 mL, which is 5 units.
  • With 2 mL the stock is 5 mg/mL, meaning 0.1 mL carries 500 mcg and the 500 mcg target needs exactly 0.1 mL, which is 10 units.
  • With 3 mL the stock is 3.333 mg/mL, meaning 0.1 mL carries roughly 333 mcg and the 500 mcg target needs 0.15 mL, which is 15 units.

Why Low PT-141 Targets Favour More Water

Take a 100 mcg PT-141 aliquot. It reads as 1 unit after 1 mL, 2 units after 2 mL and 3 units after 3 mL of water. Only the 3 mL stock lifts it above a single mark, and even so a 0.3 mL syringe or an extra intermediate dilution will measure it more reliably than a full 1 mL barrel.

Converting Bremelanotide to Molar Units

Bremelanotide is a cyclic heptapeptide of about 1,025 g/mol. A 5 mg/mL stock therefore sits near 4.9 mM, and a one micromolar solution needs roughly 1.03 mcg per mL. Because micromolar and mcg per mL line up almost one to one, PT-141 is one of the easier compounds to convert when planning receptor binding or cell assays.

Common Slip-Ups With PT-141 Numbers

  • Typing the 10 mL fill of the PT-141 nasal spray in as diluent. The spray is already a solution and never needs reconstituting.
  • Leaving the Melanotan II preset selected afterwards, which files the results under the wrong compound.
  • Entering 0.5 in the mcg field when you meant mg, making the answer a thousand times too small.
  • Misreading 15 units as 1.5 mL when it is really 0.15 mL.

PT-141 Calculator Questions

What volume of bac water suits 10mg PT-141?

Anywhere between 1 and 3 mL works. With 2 mL the stock is 5 mg per mL, which puts 50 mcg in each unit of a U-100 syringe. Using a larger volume spreads small amounts over more graduations, so they are easier to read.

Can I use this tool for Melanotan II as well?

You can. Pick Melanotan II 10mg in the presets, or simply type 10mg as the vial content. The conversion is the same for every freeze-dried peptide.

Other Peptide Calculators

Buy PT-141 (Bremelanotide)

Bacteriostatic Water

3 mL, 3 mL + 1 syringe, 10 mL, 10 mL + 1 syringe, 30 mL, 30 mL + 1 syringe

From $9
Certificate of analysisEvery research peptide comes with the certificate for its lot, listed in the COA library.
Tested identity and purityIdentity confirmed by mass spectrometry and purity measured by HPLC on every batch.
Australian stockOrders pack and ship from Australia with tracked Australia Post delivery. See delivery information.
Adults 18+ onlySold for laboratory research use only, under our research use policy.

Research use onlyAminoLab supplies research compounds for laboratory and in-vitro use, not for human or animal consumption. By continuing you confirm you are 18 or older and buying for research.

Leave